Use of them does not imply any affiliation with or endorsement by them. Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice. Tripp Lite uses primary and third-party agencies to test its products for compliance with standards. See a list of Tripp Lite's testing agencies. Email Sales.
Email Support. See all contact options. Need help with your purchase? We're always available to help with questions, including product selection, sizing, installation and product customization. Tripp Lite W. Clear All.
Contact Us. Let's get started Get Support. Open a Support Ticket Fill in an online form describing your issue. Support Chat Knowledgeable product specialists are available now. Start Chatting. Call Us When you need immediate help, call us! Let us help. On-Site Services. How to Order On-Site Services for Your 3-Phase UPS Our factory-trained technicians provide a range of on-site services, including commissioning, maintenance and repairs, to help ensure your 3-phase UPS systems maintain peak performance over their entire operational life.
How to Order Services for Your Tripp Lite Product Our factory-trained technicians provide a range of services, including commissioning, maintenance and repairs, to help ensure your Tripp Lite products maintain peak performance over their entire operational life. Contact a Tripp Lite Service Specialist intlservice tripplite.
Sales Support You are interested in purchasing a Tripp Lite product but have questions. International Support You are a distributor, reseller, or customer located outside the United States. All Images. Go to Product Page Need Help? Support History. Design Resources One or more views of this model are included in the following Visio stencil.
Product Warranty. Tripp Lite's Return Policy. Proof of Warranty Coverage You must provide proof that the product is covered under warranty. Shipping Returns You are responsible for all transportation, insurance, duties and other similar charges for returned products.
Repair or Replacement Tripp Lite will repair or replace the product at Tripp Lite's option and ship the repaired or replaced product back to you at no charge. Ask a Question. Product Page Feedback. Product Page Feedback If you need immediate assistance, please contact us.
Tell us about the issue characters or less : If you would like someone to contact you, please provide your email address: Submit. This manual contains instructions and warnings that must be followed during the installation of the products described in this manual.
Read ALL instructions before attempting to install these products. It is also suitable for supplemental cooling in large IT rooms and data centers. The following installation instructions are applicable to any application. Concrete floors and walls should be treated with a rubberor plastic-based paint. For major repairs requiring side access, 20 in.
This may necessitate moving the unit from its installation site. At least 48 in. Using a forklift or pallet jack, move the unit as close to its permanent installation location as possible before unpacking it and removing it from the shipping pallet. Ensure that the installation site provides sufficient front, back and side clearances. The unit can be positioned in a row of rack enclosures, or in a stand-alone configuration.
If the floor slope is excessive, choose another installation site. The unit is furnished with casters for final placement in its installation location. The casters are intended to move the unit over a short distance on a level, smooth, stable surface only. They are not designed to roll the unit over long distances. Push it into position. After the unit is positioned in its permanent installation location, it must be leveled. Using an 18 mm open-end wrench, lower each leveler until it reaches the floor.
There are four levelers, two at the front and two at the rear. Make sure each leveler contacts the floor solidly. Lower a leveler by turning it clockwise; raise a leveler by turning it counter-clockwise. Adjust the levelers as required until the unit is level. For additional stability, the two shipping brackets and their associated hardware may be used to secure the unit to mounting points on the floor.
Using a 13 mm open-end wrench, connect the brackets to the outer or inner bracket mounting points of the unit. If necessary, remove screws from the baying connection points of the adjoining racks. Adjust the position of the unit as required and tighten all screws. If the condenser airspace is a drop ceiling plenum and is connected to a building cooling system return, the unit should be installed using the flexible air ducts ducted through the ceiling tiles.
This is the preferred method for managing condenser air. For proper operation, the plenum must provide adequate airflow volume within the allowable temperature range, and be capable of continuously treating heat rejected by the unit.
This requires:. The condenser air must be treated by the building cooling system or exchanged with outdoor air. If the building cooling system has night and weekend setbacks, is shut down during the off-season, shut down for maintenance, or has limited excess capacity, an alternative to the standard installation may be required. Caution: A very large plenum is not a substitute for proper ventilation and heat rejection.
Heat rejected into the plenum must be able to exit the facility. Otherwise, heat buildup in the plenum will cause the unit to shut down. Install two supply flex duct tubes to the front and two exhaust flex duct tubes to the back of the unit.
All four tubes must be ducted out of the conditioned room. Take installation requirements into consideration when deciding where to run the flexible ducts.
Ensure that the four duct tubes are similar in length, with no sharp bends. To prevent hot air from bypassing the airflow between the exhaust and supply air duct, ensure that the two exhaust tubes rear protrude higher above the ceiling tile than the intake tubes by a minimum of 6 inches.
Caution: Use only the provided ducts when making condenser ventilation connections. Any additional length of ducting may significantly degrade the performance of the unit.
Additional hardware for this application must be user supplied; it is not included with the unit. The following requirements apply:. Caution: Unconditioned air imposes extreme load variation on the cooling equipment from summer to winter, resulting in higher system operating costs. Equipment performance should be monitored to ensure that the venting installation is working properly. This bracket must be removed prior to operating the unit.
Caution: Do not loosen or remove the bolts attaching the compressor to the bottom of the unit. During normal operation, the amount of water removed from the air is minimal; however, if the amount of water removed from the air exceeds the capability of the internal removal system 0.
Install the auxiliary drain line C. Route the unattached end of the auxiliary drain line to a nearby drain or other water removal method. Auxiliary drain line is 6 ft. For drainage at a longer distance, user must supply longer compatible drain line. This is typically due to voltage incompatibility. If you believe this to be an error or you would like assistance finding a product designed for your country, please contact us.
Tripp Lite joined the Eaton family in March Eaton has long been a premier name in backup power and power management. The acquisition of Tripp Lite transforms Eaton's distributed IT infrastructure and connectivity equipment capabilities. Combining our product strengths and expert personnel allows us to offer comprehensive and innovative solutions for critical power and digital infrastructure applications, backed by quality, service and support you can trust.
Learn more. All product and company names are trademarks or registered trademarks of their respective holders. Use of them does not imply any affiliation with or endorsement by them. Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice. Tripp Lite uses primary and third-party agencies to test its products for compliance with standards.
See a list of Tripp Lite's testing agencies. Email Sales. Email Support. See all contact options. Need help with your purchase?
0コメント